July 17th, 2003
RAQ Fileserver
Ok, large drive support works fine on Debian 3.0 mips. This is good news…. you can check out the dmesg output below.
CPU revision is: 000028a0
FPU revision is: 000028a0
Primary instruction cache 32kb, linesize 32 bytes.
Primary data cache 32kb, linesize 32 bytes.
Linux version 2.4.18 (root@qube) (gcc version 2.95.4 20011002 (Debian prerelease)) #2 Fri May 31 17:40:33 BST 2002
Determined physical RAM map:
memory: 10000000 @ 00000000 (usable)
On node 0 totalpages: 65536
zone(0): 65536 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0,115200 root=/dev/hda1
Calibrating delay loop… 249.85 BogoMIPS
Memory: 255944k/262144k available (1243k kernel code, 6200k reserved, 160k data, 76k init, 0k highmem)
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Checking for ‘wait’ instruction… available.
POSIX conformance testing by UNIFIX
PCI: Probing PCI hardware
Cobalt Board ID: 6
Activating ISA DMA hang workarounds.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
pty: 256 Unix98 ptys configured
Cobalt LCD Driver v2.10
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0xc800000 (irq = 7) is a ST16650V2
rtc: SRM (post-2000) epoch (2000) detected
Real Time Clock Driver v1.10e
block: 128 slots per queue, batch=32
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 49
PCI: Enabling device 00:09.1 (0285 0280)
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c586a (rev 27) IDE UDMA33 controller on pci00:09.1
ide0: BM-DMA at 0xcc00-0xcc07, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xcc08-0xcc0f, BIOS settings: hdc:pio, hdd:pio
hda: ST360015A, ATA DISK drive
hdb: ST360015A, ATA DISK drive
hdc: IRQ probe failed (0xfffffefa)
hdc: IRQ probe failed (0xfffffefa)
hdd: IRQ probe failed (0xfffffefa)
hdd: IRQ probe failed (0xfffffefa)
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=116301/16/63
hdb: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=116301/16/63
Partition check:
hda: hda1 hda2 hda3 hda4
hdb: unknown partition table
Linux Tulip driver version 0.9.15-pre9 (Nov 6, 2001)
PCI: Enabling device 00:07.0 (0045 0280)
tulip0: Old format EEPROM on ‘Cobalt MicroServer’ board. Using substitute media control info.
tulip0: EEPROM default media type Autosense.
tulip0: Index #0 – Media MII (#11) described by a 21142 MII PHY (3) block.
tulip0: MII transceiver #1 config 1000 status 7809 advertising 01e1.
eth0: Digital DS21143 Tulip rev 65 at 0x100000, 00:10:E0:00:E9:84, IRQ 4.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 76k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Adding Swap: 262576k swap-space (priority -1)
eth0: Setting full-duplex based on MII#1 link partner capability of 41e1.
hdb: hdb1 hdb2 hdb3 hdb4
hdb: hdb1 hdb2 hdb3 hdb4